Loading ...

Dewatering and groundwater control | Stuart Well Services Ltd

Landfill Products

Landfill Products

Stuart Well Services is able to supply a range of well linings for site investigations, dewatering wells, leachate abstraction wells, water abstraction wells, soakaways and gas abstraction wells.

Landfill Borehole Lining Systems

Stuart Well Services is able to supply a range of well-linings for site investigations, dewatering wells, leachate abstraction wells, water abstraction wells, soakaways and gas abstraction wells.

All materials are manufactured to meet the requirements of: ISO9001:1994 by Jain Irrigation S Limited.

Pipes are male-female threaded in lengths of 1 and 3 metres.

  • Manufactured from high density Polyethylene (HDPE)
  • High temperature resistance
  • Vicat softening point 125ยบ ISO R 306 (B)
  • Resistant to aggressive chemical found in landfill sites
  • High strength, tough and durable
  • Threaded without reducing wall thickness giving maximum strength of joint with rapid assembly - flush joints also available
  • Metric sizes to suit all horizontal pipework
  • Manufactured to DIN 8074
  • Landfill site proven for over 10 years

  • Outside Diameter (mm) Inside Diameter (mm) Weight (kg/m)
    40 28 0.60
    63 51.4 1.05
    90 73.6 2.12
    110 97.4 2.08
    160 141.8 4.35

    Other dimensions and wall thickness are available on request up to 630mm diameter.

    Slot sizes 1mm standard, 0.75mm available on request.

    Methane Gas Venting Stacks

    Cowl Rotorvent
    • Methane gas venting is actively undertaken by the installation of gas venting stacks which will rotate in wind speeds as low as three kilometres per hour
    • Ventilation rates in excess of 1500 litres per minute are typically achieved with average wind speed of 16 kilometres per hour
    • The rotating cowl is available in two sizes, one suitable for pipes up to 150mm diameter (model no. RC150) and for pipes up to 200mm (model no. RC200 - see table below)
    Cowl Number RC150 RC200
    Pipe Size (mm) 70 - 150 150 - 200
    Venting Capacity (l.p.m, max) 1500 2800
    Sample Port (mm) 25 25
    Sleeve Length (mm) 3500 3500
    Cage Size (HWD mm) 360 x 380 x 380 360 x 380 x 380
    Lugs (mm) 400 400

    Flux Boxes

    A Flux Box

    Monitoring landfill gas surface emissions

    The objective of a flux box survey is to quantify the total releases of methane from the surveyed area. This may identify places where the gas flux through the cap exceeds an emission standard set by the regulator and so will initiate further remedial work, for IPPC compliance.

    Guidance on monitoring landfill gas surface emissions

    A passive flux box consists of an enclosure of known volume, with two ports fitted to the upper surface.

    Flux box valve Inlet Port

    The inlet port is used for pressure equilibration and the outlet port for obtaining samples.

    This arrangements facilitates the sampling of gases without the disturbing the pressure within the flux box.

    The methane concentration inside the box is analysed using a gas analyser (not supplied).

    The passive flux box is manufactured from white polyethylene (as recommended by the Environment Agency) to reduce thermal differentials between the inside and the outside of the box in warm weather.

    Flux box valve Outlet Port

    The box is lightweight, less than 10 Kg and easy for site personnel to carry a set of flux boxes.

    Accreditations and Associations

    ISO-9001 ISO-14001
    ISO-22301 ISO-45001
    ISO-45001
    ISO-45001
    ISO-45001
    The Temporary Works Forum (TWf)